10.4.2. HSPICE simulator interfaceΒΆ

This demo shows how to use the HSPICE simulator interface.

Read chapter SPICE OPUS simulator interface to learn about the circuit and its description. The file names are the same as in the SPICE OPUS example, except that the files are using the HSPICE syntax.

File: demo/evaluation/01-simulator-hspice/runme.py

# Test HSPICE simulator interface

from pyopus.simulator import simulatorClass

if __name__=='__main__':
	# Job list for simulator
	jobList=[
		{	# First job - op analysis
			'name': 'dcop', 
			'definitions': [
				{ 'file': 'cmos180n.lib', 'section': 'tm' }, 
				{ 'file': 'opamp.cir' }
			], 
			'params': {
				'vdd': 1.8, 
				'temperature': 25
			}, 
			'options': {
				'method': 'trap'
			}, 
			'saves': [
			], 
			'command': 'op()'
		},
		{	# Second job - op analysis with different temperature
			'name': 'dcop100', 
			'definitions': [
				{ 'file': 'cmos180n.lib', 'section': 'tm' }, 
				{ 'file': 'opamp.cir' }
			], 
			'params': {
				'vdd': 1.6, 
				'temperature': 100
			}, 
			'options': {
				'method': 'trap'
			}, 
			'saves': [
			], 
			'command': 'op()'
		},
		{	# Third job - op analysis with different supply voltage
			'name': 'dcopv33', 
			'definitions': [
				{ 'file': 'cmos180n.lib', 'section': 'tm' }, 
				{ 'file': 'opamp.cir' }
			], 
			'params': {
				'vdd': 2.0, 
				'temperature': 25
			}, 
			'options': {
				'method': 'trap'
			}, 
			'saves': [
			], 
			'command': 'op()'
		},
		{	# Fourth job - op analysis with different library
			'name': 'dcopff', 
			'definitions': [
				{ 'file': 'cmos180n.lib', 'section': 'ws' }, 
				{ 'file': 'opamp.cir' }
			], 
			'params': {
				'vdd': 2.0, 
				'temperature': 25
			}, 
			'options': {
				'method': 'trap'
			}, 
			'saves': [
			], 
			'command': 'op()'
		}, 
		{	# Fifth job - op analysis with different library
			'name': 'dcopff100', 
			'definitions': [
				{ 'file': 'cmos180n.lib', 'section': 'ws' }, 
				{ 'file': 'opamp.cir' }
			], 
			'params': {
				'vdd': 2.0, 
				'temperature': 100
			}, 
			'options': {
				'method': 'trap'
			}, 
			'saves': [
			], 
			'command': 'op()'
		}
	]

	# Input parameters
	inParams={
		'mirr_w': 7.46e-005, 
		'mirr_l': 5.63e-007
	}

	# Create simulator, load HSpice class on demand. 
	sim=simulatorClass("HSpice")(debug=10)

	# Set job list and optimize it
	sim.setJobList(jobList)

	# Print optimized job groups - need to get them manually from simulator
	# because jobGroupCount() and jobGroup() behave as if there is only one 
	# job group holding all jobs. All simulations are performed with a single 
	# simulator call. 
	# Internally jobs are grouped according to the circuit topology. 
	# We display here this internal grouping.  
	jobSeq=sim.jobSequence
	print("\nJob Groups:")
	for i in range(len(jobSeq)):
		group=jobSeq[i]
		gstr=''
		for j in group:
			gstr+=" %d (%s), " % (j, jobList[j]['name'])
		print("  %d: %s" % (i, gstr))

	print("")
	# Set input parameters
	sim.setInputParameters(inParams)

	# Go through all job groups, write file, run it and collect results
	ngroups=sim.jobGroupCount()
	for i in range(ngroups):
		# Run jobs in job group. 
		(jobIndices, status)=sim.runJobGroup(i)
		
		print("")
		for j in jobIndices:
			# Job name
			jobName=jobList[j]['name']
			# Load results
			res=sim.readResults(j, status)
			# Print results
			if res is not None:
				print("Job %d (%s): Vout=%e" % (j, jobName, res.v("out")))
			else:
				print("Job %d (%s): no results" % (j, jobName))
		print("")

	sim.cleanup()